Batteries
What is the difference between a Deep Cycle Battery and a Starting Battery?
A deep-cycle battery has the ability to be deeply discharged and charged many times during its service life. It is designed specifically for powering electrical equipment for long periods of time. An automotive or starting battery is designed for brief bursts of high current and cannot withstand more than a few deep discharges before failure. This is why it is unable to start your car if you accidentally leave the lights on more than a couple of times.
Can I use my deep-cycle battery as a starting battery?
Some deep-cycle batteries can be used for engine starting, but starting batteries should not be used for deep-cycle applications. A deep-cycle battery may have less cranking amps per pound than a starting battery, but in most cases a deep-cycle battery is still more than adequate for the purpose of starting an engine in emergency situations. We would not recommend using a Deep-Cycle battery in place of a Starting battery.
What are the advantages and disadvantages of AGM, Gel, and Flooded / Wet Cell Lead Acidand Lithium LiFePO4 Deep Cycle Batteries?
Lithium batteries offer the best performance with zero maintenance, but are the most expensive. Flooded lead acid batteries are the most cost efficient but need regular maintenance. AGM and Gel batteries require zero maintenance and offer better performance than FLAs, but do not provide as much power as lithium batteries.
AGM batteries are sensitive to depth of discharge. This means the deeper the battery is discharged, the fewer cycles it has. AGM batteries are generally recommended to only be discharged to 50% of their capacity to maximize their cycle life. This limited depth of discharge (DOD) of 50% means that more batteries are required to achieve the desired capacity. This means more upfront costs, and more space needed to store them.
A lithium (LiFePO4) battery, on the other hand, is not affected much by depth of discharge so it boasts a much longer cycle life. Its DOD of around 80% means fewer batteries are required to achieve the desired capacity. Fewer batteries mean less space needed to store them.
While lithium batteries may have advantages, AGM batteries still have proven time-tested technology as they have been around much longer. AGM's also have the upper hand when it comes to charging in freezing (below zero degrees Celsius) temperatures - albeit, with a bit of a hit to its efficiency. Unlike AGM's, lithium batteries require temperature regulation for use in below-freezing temperatures.Lithium batteries have the added bonus of not containing the heavier lead-acid found in AGM's, therefore, are much lighter. Since their DOD is 80-90%, lithium a battery bank generally occupies less space. (Less batteries are required for a desired capacity.) Because of this, lithium batteries can save quite a bit of volume and weight in comparison to the traditional AGM's.
The depth of discharge of a battery refers to the percentage of the battery that has been discharged (used) relative to its overall capacity within a charge cycle. A lithium battery with an overall capacity of 100Ah (amp hours) will give you 80Ah (or discharge to 80%), while AGM's offer 50Ah (or discharge of 50%) before needing to recharge.
Based on these numbers, AGM's are the better option for those who use their RV only a few months at a time, and lithium batteries are preferable for those who are off-grid all the time.
Connecting in Series (Increases Voltage)
In connecting batteries in series the positive terminal of the first battery is connected to the negative terminal of the second battery and so on down the string.
The interconnecting cables must be of equal length and resistance to insure equalization of the load. All batteries in the string will receive the same amount of charge current, though individual battery voltages may vary.
High voltage strings of batteries in series should be limited to twenty 6 volt or ten 12 volt batteries when a single constant voltage charger is connected across the entire string. Differences in capacity can cause some batteries to overcharge while others remain undercharged thus causing premature aging of batteries. It is, therefore, not advisable to mix batteries of different capacities, make, or age in a series string.
Connecting in Parallel (Increases Capacity)
When charging batteries in parallel (positive terminals are connected to the positive terminal and negative terminals to the negative), all batteries in the string will receive the same charge voltage but the charge current each battery receives will vary until equalization is reached.
Charging in Series
Lead-acid batteries are strings of 2 volt cells connected in series, commonly 2, 3, 4 or 6 cells per battery. Strings of Power-Sonic batteries, up to 48 volts and higher, may be charged in series safely and ef ciently. However, as the number of batteries in series increases, so does the possibility of slight differences in capacity. These differences can result from age, storage history, temperature variations or abuse.
Fully charged batteries should never be mixed with discharged batteries when charging in series. The discharged batteries should be charged before connection.
When a single constant voltage charger is connected across an entire high voltage string, the same current ows through all cells in the string. Depending on the characteristics of the individual batteries, some may overcharge while others remain in a slightly undercharged condition.
To minimize the effects of individual battery differences, use batteries of the same age, amp hour, and history and, if possible, charge in strings of no greater than 24 or 48 volts.
Charging in Parallel
When connected in parallel, the current from a charger will tend to divide almost equally between the batteries. No special matching of batteries is required. If the batteries of unequal capacity are connected in parallel, the current will tend to divide between the batteries in the ratio of capacities (actually, internal resistances).
When charging batteries in parallel, where different ratios of charge are to be expected, it is best to make provisions to assure that the currents will not vary too much between batteries.
EVE Prismatic LFP Lithium Rechargeable Cells LiFePO4
EVE is an expert and leader in developing and manufacturing of lithium battery, including lithium thionyl chloride (Li/SOCl2) cells, lithium manganese dioxide (Li/MnO2) cells, Lithium rechargeable cells, and can provide customized portable power source solutions and OEM services.
EVE has an experienced R&D team, with more than 20 years experience, many patents and advanced equipments.
EVE continually develops new technology in battery design and production, and implements advanced management systems such as 5S, 6 Sigma, Lean Production and SPC. EVE has been ISO9001 certified, and also recognized by UL, UN, CE and CCC.
Recently, EVE just acheived the ISO/TS 16949:2009.
EVE LiFePO4 12v Battery Packs
.jpg)
We use 3.2v LFP Lithium Cells to make up deep cycle lithium battery banks
The benefits of using 3.2v Lithium Cells together in a battery bank over a encased Lithium Battery are numerous.
If you drop a cell in a encased battery you have to replace the battery, if you drop a cell in a bank of cells, you simply replace the cell. This works out much cheaper and economically in the long run.
The other benefit of using cells is both weight and physical size. Cells work out a couple of KG lighter than encased batteries do so this is even more weight saving!!
They can also be configured in a number of different orientations both vertically and horizontally, so you can have a range of varying dimensions to fit many different install locations. i.e. long thin battery banks, or short stubbier battery banks. The Cells can be arranged in a 4x1, 2x2 or 1x4 configuration to fit in those tight spots.
EVE LFP LiFePO4 Cells have a 3500 cycle life & are maintenance free
.jpg)
Connect in series for 24v, 36v or 48v Battery Bank, or Connect in Parallel for Larger Capacity:
105Ah Cells
- 1 set of 4pcs 3.2v 105Ah cells can form a 12v 105Ah battery pack.
- 2 sets of 4pcs 3.2v 105Ah cells can form a 24v 105Ah battery pack or a 12v 210A battery pack.
- 4 sets of 4pcs 3.2v 105Ah cells can form a 48v 105Ah battery pack or a 24v 210A battery pack or a 12v 420Ah battery pack.
304Ah Cells
- 1 set of 4pcs 3.2v 304Ah cells can form a 12v 304Ah battery pack.
- 2 sets of 4pcs 3.2v 304Ah cells can form a 24v 304Ah battery pack or a 12v 608A battery pack.
- 4 sets of 4pcs 3.2v 304Ah cells can form a 48v 304Ah battery pack or a 24v 608A battery pack or a 12v 1216Ah battery pack.
.jpg)
Model |
LF105 |
LF304 |
|---|---|---|
TYPICAL CAPACITY |
106.5 Ah @ 1.0C discharge |
304.0 Ah @ 1.0C discharge |
MINIMUM CAPACITY |
105.0 Ah @ 1.0C discharge |
303.0 Ah @ 1.0C discharge |
TYPICAL VOLTAGE |
3.2V |
3.2V |
AC IMPEDENCE RESISTNCE |
<0.5 Ohm |
<0.5 Ohm |
CHARGE CURRENT (CC/CV) |
Max. Charge Current: 1C Cut Off Voltage: 3.65V |
Charge/Discharge Current : 0.5C / 0.5C Charge/Discharge Cut Off Voltage: 3.65V / 2.5V |
DISCHARGE |
Max. Discharge Current: 3C Cut Off Voltage: 2.5V |
Continuous Charge/Discharge Current : 250A Pulse Charge/Discharge Cut Off Voltage: 2C / 2C |
RECOMMENDED SOC WINDOW |
SOC: 10 - 90% |
SOC: 10 - 90% |
CYCLE LIFE |
>3500 |
>3500 |
CHARGING TEMPERATURE |
0°c to +55°c |
0°c to +60°c |
DISCHARGING TEMPERATURE |
-20°c to +55°c |
-30°c to +60°c |
STORAGE TEMPERATURE |
-20°c to +45°c |
-20°c to +45°c |
STORAGE HUMIDITY |
<70% |
<95% |
DIMENSIONS (LxWxH) |
130 x 37 x 196 (201) mm |
173 x 72 x 204 (208) mm |
WEIGHT |
1.98 KG |
5.49 KG |
| EVE 12v 105A LiFePO4 Battery Bank with 100A BMS | |||
| Lithium | Battery Pack 12v 105A | $850.00 |  |
| EVE 12v 304A LiFePO4 Battery Bank with 250A BMS | |||
| Lithium | Battery Pack 12v 304A | $1850.00 | |
EVE LF105 3.2v 105A LiFePO4 Cells
EVE deep cycle lithium iron phosphate (LiFePO4) battery cells are mainly used Energy storage Systems, in Electric Vehicles and Electric Boats.
Using them you can easily set up your own 12v, 24v, 48v energy storage system. As their quality is already well known, they have become one of the trusted and popular cells among lithium iron phosphate battery users.
The benefits of using 3.2v Lithium Cells together in a battery bank over a encased Lithium Battery are numerous.
If you drop a cell in a encased battery you have to replace the battery, if you drop a cell in a bank of cells, you simply replace the cell. This works out much cheaper and economically in the long run.
The other benefit of using cells is both weight and physical size. Cells work out a couple of KG lighter than encased batteries do so this is even more weight saving!!
They can also be configured in a number of different orientations both vertically and horizontally, so you can have a range of varying dimensions to fit many different install locations. i.e. long thin battery banks, or short stubbier battery banks. The Cells can be arranged in a 4x1, 2x2 or 1x4 configuration to fit in those tight spots.
We use 3.2v LFP Lithium Cells to make up deep cycle lithium battery banks. We supply both fully setup battery banks with BMS and Balancers as well as individual parts incase you need to replace a Cell, a BMS or a Balance Board.
EVE LFP LiFePO4 Cells have a 3500 cycle life & are maintenance free
Connect in series for 24v, 36v or 48v Battery Bank, or Connect in Parallel for Larger Capacity:
- 1 set of 4pcs 3.2v 105Ah cells can form a 12v 105Ah battery pack.
- 2 sets of 4pcs 3.2v 105Ah cells can form a 24v 105Ah battery pack or a 12v 210A battery pack.
- 4 sets of 4pcs 3.2v 105Ah cells can form a 48v 105Ah battery pack or a 24v 210A battery pack or a 12v 420Ah battery pack.
Model |
LF105 |
|---|---|
TYPICAL CAPACITY |
106.5 Ah @ 1.0C discharge |
MINIMUM CAPACITY |
105.0 Ah @ 1.0C discharge |
TYPICAL VOLTAGE |
3.2V |
AC IMPEDENCE RESISTNCE |
<0.5 Ohm |
CHARGE CURRENT (CC/CV) |
Max. Charge Current: 1C Cut Off Voltage: 3.65V |
DISCHARGE |
Max. Discharge Current: 3C Cut Off Voltage: 2.5V |
RECOMMENDED SOC WINDOW |
SOC: 10 - 90% |
CYCLE LIFE |
>3500 |
CHARGING TEMPERATURE |
0°c to +55°c |
DISCHARGING TEMPERATURE |
-20°c to +55°c |
STORAGE TEMPERATURE |
-20°c to +45°c |
STORAGE HUMIDITY |
<70% |
DIMENSIONS (LxWxH) |
130 x 37 x 196 (201) mm |
WEIGHT |
1.98 KG |
(Example of 105Ah Battery Bank pictured to the right, next to it is the BlueTooth App for your battery)
| EVE LF105 3.2v 105A LiFePO4 Cells | |||
| Lithium | 3.2v 105Ah EVE Cells | $150.00 | |
| EVE 12v 105A LiFePO4 Battery Bank with 100A BMS | |||
| Lithium | Battery Pack 12v 105A | $850.00 | |
EVE LF105 3.2v 304A LiFePO4 Cells
EVE deep cycle lithium iron phosphate (LiFePO4) battery cells are mainly used Energy storage Systems, in Electric Vehicles and Electric Boats.
Using them you can easily set up your own 12v, 24v, 48v energy storage system. As their quality is already well known, they have become one of the trusted and popular cells among lithium iron phosphate battery users.
The benefits of using 3.2v Lithium Cells together in a battery bank over a encased Lithium Battery are numerous.
If you drop a cell in a encased battery you have to replace the battery, if you drop a cell in a bank of cells, you simply replace the cell. This works out much cheaper and economically in the long run.
The other benefit of using cells is both weight and physical size. Cells work out a couple of KG lighter than encased batteries do so this is even more weight saving!!
They can also be configured in a number of different orientations both vertically and horizontally, so you can have a range of varying dimensions to fit many different install locations. i.e. long thin battery banks, or short stubbier battery banks.
The Cells can be arranged in a 4x1, 2x2 or 1x4 configuration to fit in those tight spots*. (*based on 1x4 config, other configrations may cost more)
We use 3.2v LFP Lithium Cells to make up deep cycle lithium battery banks. We supply both fully setup battery banks with BMS and Balancers as well as individual parts incase you need to repalce a Cell, a BMS or a Balance Board.
EVE LFP LiFePO4 Cells have a 3500 cycle life & are maintenance free
Connect in series for 24v, 36v or 48v Battery Bank, or Connect in Parallel for Larger Capacity:
- 1 set of 4pcs 3.2v 304Ah cells can form a 12v 304Ah battery pack.
- 2 sets of 4pcs 3.2v 304Ah cells can form a 24v 304Ah battery pack or a 12v 608A battery pack.
- 4 sets of 4pcs 3.2v 304Ah cells can form a 48v 304Ah battery pack or a 24v 608A battery pack or a 12v 1216Ah battery pack.
Model |
LF304 |
|---|---|
TYPICAL CAPACITY |
304.0 Ah @ 1.0C discharge |
TYPICAL VOLTAGE |
3.2V |
AC IMPEDENCE RESISTNCE |
<0.5 Ohm |
STANDARD CHARGE AND DISCHARGE |
Charge/Discharge Current : 0.5C / 0.5C Charge/Discharge Cut Off Voltage: 3.65V / 2.5V |
MAC CHARGE / DISCHARGE CURRENT |
Continuous Charge/Discharge Current : 250A Pulse Charge/Discharge Cut Off Voltage: 2C / 2C |
RECOMMENDED SOC WINDOW |
SOC: 10 - 90% |
CYCLE LIFE |
>3500 |
CHARGING TEMPERATURE |
0°c to +60°c |
DISCHARGING TEMPERATURE |
-30°c to +60°c |
STORAGE TEMPERATURE |
-20°c to +45°c |
STORAGE HUMIDITY |
<95% |
DIMENSIONS (LxWxH) |
173 x 72 x 204 (208) mm |
WEIGHT |
5.49 KG |
(Example of 304Ah Battery Bank pictured to the right, next to it is the BlueTooth App for your battery)
| EVE LF105 3.2v 304A LiFePO4 Cells | |||
| Lithium | EVE LF304 3.2v 304Ah | $310.00 | |
| EVE 12v 304A LiFePO4 Battery Bank with 250A BMS | |||
| Lithium | Battery Pack 12v 304A | $1850.00 | |
Deligreen 4S Smart BlueTooth BMS Range
Deligreen is a one stop power system provider, engaged in research and development and sales of lithium battery and its accessories.
The main products are the distribution of large cell of domestic famous brand, BMS, Active balancer, charger, home energy storage and electric vehicle charging cable.
A BMS (Battery Management System) is essential in a Lithium-Ion battery system.
This device manages a real-time control of each battery cell, communicates with external devices, manages SOC calculation, measures temperature and voltage, etc.
Intellegent Control Accurate Data
Monitor the Battery status in Real-Time base by checking the battery capacity and observing the voltage of each string in Real-Time.
Real-Time Positioning
Remote Power Off
Remote Sofware Upgrade
UART: UART is Universal Asynchronous Receiver/Transmitter, It transforms the data to be transmitted between serial communication and parallel communication. As a chip to convert parallel input signals into serial output signals, UART is usually integrated into other communication interfaces.
Model |
100 |
200 |
250 |
300 |
500 |
|---|---|---|---|---|---|
Constant Discharge Current |
100A |
200A |
250A |
300A |
500A |
Over-Discharge Current Protection |
300A +- 50A |
600A +- 100A |
600A +- 100A |
1000A +- 200A |
1500A +- 200A |
Charge Voltage |
Series.No *3.65V |
||||
Charge Current |
50A |
100A |
125A |
150A |
250A |
Over Charge Volt |
3.75v +- 0.05V |
3.75v +- 0.025V |
|||
Over Charge Volt Protect Delay |
1 Second |
||||
Over Charge Volt Release |
3.55v +- 0.05V |
||||
Power Balance Volt |
3.5v |
||||
Balance Release Volt |
3.5v |
||||
Balance Current |
35 +- 5mA |
200 +- 50mA |
|||
Over Discharge Detect Volt |
2.2v +- 0.1V |
||||
Over Discharge Detect Delay |
1 Second |
||||
Over Discharge Volt Release |
2.7v +- 0.05V |
||||
Over Current Detect Delay |
1 millisecond |
||||
Over Current Protect Release |
Off-Load |
||||
Short Circuit Protection |
External load short circuit |
||||
Short Circuit Detect Delay |
1 millisecond |
||||
Short Circuit Detect Release |
Off-Load |
||||
Temp Protection |
Charge 0°c Discharge 70°c |
||||
Main Circuit Resistor |
<20 Milliohm |
||||
Working Current |
500 Microamps |
||||
Sleepy Current (When Battery is Over Discharged) |
<20 Microamps |
||||
Working Temp Range |
-20°c to +70°c |
||||
Storage Temp Range |
-40°c to +80°c |
||||
| Deligreen 4S Smart BlueTooth BMS Range | |||
| DALYBT | Lithium BMS 100A 12v 4s | $149.99 | |
| DALYBT | Lithium BMS 200A 12v 4S | $375.00 | |
| DALYBT | Lithium BMS 250A 12v 4s | $345.00 | |
| DALYBT | Lithium BMS 250A 24v 8s | $375.00 | |
| DALYBT | Lithium BMS 300A 12v 4s | $545.00 | |
| DALYBT | Lithium BMS 300A 24v 8s | $567.00 | |
| DALYBT | Lithium BMS 500A 12v 4s | $675.00 | |
| DALYBT | Lithium BMS 500A 24v 8s | $745.00 | |
| Deligreen 4S Non BlueTooth BMS Range | |||
| DALY | Lithium BMS 100A 12v 4s | $120.00 | |
| DALY | Lithium BMS 200A 12v 4S | $225.00 | |
Heltech 3S 4S 5A Active Balancer
Whole Group Balancer 3S 4S 5A Active Balancer Lifepo4 Lithium Lipo Battery Energy active equalization module Fit Capacitor
Active balancing is a technique that improves the battery life by maximizing the capacity of a battery pack with multiple cells, ensuring that all of its energy is available for use.
Working principle:
The capacitor fit transfers the charge carrier, and the balancing work is started when the balancing board is connected to the battery.
The original brand new ultra-low internal resistance MOS, 2OZ copper thick PCB, balancing current 0-5.5A, the more the balancing current, the smaller the battery.
Reserve the wiring position of the dormant switch, the operating current in dormant power-off mode is less than 0.1mA, and the equilibrium voltage accuracy is within 5mv
WORKING CONDITIONS |
TERNARY LITHIUM / LFP LITHIUM IRON PHOSPAHTE PARAMATERS |
|---|---|
Balanced Starting Voltage |
3.0V - 4.2V |
Balanced Termination Voltage |
2.9v (into undervoltage sleep state) |
Balance Accuracy |
<5 mV |
Sleeping Current |
<1 mV |
Maximum Balance Current |
The whole Group Error is: 0.1V/1A; 0.5V/3.5A; 1.0V/5.5A |
3S Quiescent Current |
Full Power State (4.2V*3 Cell) 12.6V 12mA |
4S Quiescent Current |
Full Power State (4.2V*4 Cell) 16.5V 15mA |
7S Quiescent Current |
Full Power State (4.2V*7 Cell) 29.4V 15mA |
8S Quiescent Current |
Full Power State (4.2V*8 Cell) 33.6V 11mA |
15S/16S/17S on same board Quiescent Current |
Full Power State (4.2V*17 Cell) 71.4V 10mA |
Whether External Power Supply is Required |
No External Power Supply Needed - The whole group is balanced by the internal energy transfer of the battery |
Working Environment Temperature |
-0°c to +60°c |
(Example of Active Balancer used in 304Ah Battery Bank pictured to the right)
| Heltech 3S 4S 5A Active Balancer | |||
| BATLIB4S12CAP | Active Balancer | $49.99 | |
| BATLIB8S24CAP | Active Balancer | $79.99 | |
PowerSonic Sealed AGM Deep Cycle Batteries
Power Sonic Batteries Corporation has more than 50 years experience in the battery industry.
Powersonic Batteries is headquartered in San Diego, California.
From their inception in 1970, their total focus has been the design, manufacture, and distribution of innovative battery solutions
Their products are sold in over 70 countries worldwide for a broad range of electronic and industrial applications, where cost effective DC power is required.
In addition, they are constantly developing new products to keep pace with industry’s rapidly changing needs.
The continuous improvement of our engineering processes allows us to develop products with better value and/or performance.
Power Sonic batteries has subsidiary companies in the U.K and Europe, Singapore and Mexico.
PowerSonic PDC Series 12-Volt AGM Deep Cycle Batteries
Power-Sonic deep cycle PDC range is purpose built for those applications which require regular and consistent cycling (charge and dis-charge). Commonly called deep cycling the oversized negative plates and a specialised paste formulation of the PDC can provide constant power for longer periods of time without shortening the life of the battery.
Typical applications include: weekend or holiday homes with large electrical loads, medium solar systems for industrial applications, small solar and wind-driven power plants, offshore buoys, yachts, measurement stations.
PowerSonic Batteries are designed in America and manufactured in China, Taiwan & Vietnam and covered by a 12 month warranty
Features:
- Absorbent Glass Mat (AGM) technology for superior performance
- Valve regulated, spill proof construction for safe operation in any position
- Oversize negative plates and a specialized paste formulation for true deep cycle performance.
- Special additives in the paste ensure superior performance in deep discharge situations.
- Power/volume ratio yielding unrivalled energy density
- Rugged impact resistant ABS case and cover (UL94-HB)
- Approved for transport by air. D.O.T., I.A.T.A., F.A.A. and C.A.B. certified
- L. certified
Applications:
- Mobility Scooters
- Electric Bikes
- Caravans
- Marine
- Camping
Model |
Description |
Nominal Voltage V |
Rated Capacity (AH) 20-hr |
Rated Capacity (AH) 10-hr |
CCA |
Length mm |
Width mm |
Height mm |
Ht. Over Terminal mm |
Weight kgs |
Terminal Type Standard |
|---|---|---|---|---|---|---|---|---|---|---|---|
PDC12140 |
12v 13.9 ah C20 Cyclic AGM |
12 |
13.9 |
13.00 |
200 |
151 |
98 |
95 |
101 |
4.2 |
F2 |
PDC12200 |
12v 21 ah C20 Cyclic AGM |
12 |
21.0 |
20.00 |
220 |
182 |
77 |
164 |
167 |
6.6 |
NB |
PDC12260 |
12v 28 ah C20 Cyclic AGM |
12 |
28.0 |
26.00 |
260 |
167 |
175 |
125 |
125 |
9.8 |
NB2 |
PDC12350 |
12v 35.4 ah C20 Cyclic AGM |
12 |
35.4 |
33.00 |
300 |
195 |
130 |
164 |
180 |
11.2 |
NB |
PDC12480 |
12v 48 ah C20 Cyclic AGM |
12 |
48.0 |
38.00 |
400 |
197 |
165 |
170 |
170 |
14.5 |
B (T6) |
PDC12600 |
12v 59 ah C20 Cyclic AGM |
12 |
60.0 |
55.00 |
420 |
230 |
138 |
220 |
230 |
17.7 |
U (T9) |
PDC12800 |
12v 80 ah C20 Cyclic AGM |
12 |
80.4 |
75.00 |
480 |
260 |
168 |
208 |
214 |
21.0 |
U (T14) |
PDC121050 |
12v 105 ah C20 Cyclic AGM |
12 |
105.0 |
95.00 |
750 |
306 |
168 |
210 |
229 |
29.6 |
U (T14) |
PDC121250 |
12v 125 ah C20 Cyclic AGM |
12 |
125.0 |
120.00 |
800 |
330 |
173 |
212 |
220 |
31.4 |
T11 |
PDC121600 |
12v 160 ah C20 Cyclic AGM |
12 |
160.0 |
150.00 |
950 |
485 |
170 |
240 |
240 |
42.5 |
B (T6) |
PDC122000 |
12v 215 ah C20 Cyclic AGM |
12 |
214.4 |
200.00 |
1054 |
522 |
240 |
218 |
224 |
62.5 |
B (T11) |
PDC122500 |
12v 268 ah C20 Cyclic AGM |
12 |
268.0 |
250.00 |
1250 |
522 |
268 |
220 |
226 |
73.0 |
T11 |
*OTHER AMPERAGES MAY BE AVAILABLE UPON REQUEST
| PowerSonic PDC Series AGM Deep-Cycle Batteries | |||
| BATPDC1214 | D/Cycle 12V 14A AGM | $74.99 | |
| BATPDC1220 | D/Cycle 12V 20A AGM | $109.99 | |
| BATPDC1226 | D/Cycle 12V 28A AGM | $139.99 | |
| BATPDC1235 | D/Cycle 12V 35A AGM | $155.00 | |
| BATPDC1248 | D/Cycle 12V 48A AGM | $166.00 | |
| BATPDC1260 | D/Cycle 12V 59A AGM | $245.00 | |
| BATPDC1280 | D/Cycle 12V 80A AGM | $305.00 | |
| BATPDC12105 | D/Cyc 12V 105A AGM | $350.00 | |
| BATPDC12125 | D/Cyc 12V 125A AGM | $397.00 | |
| BATPDC12160 | D/Cyc 12V 161A AGM | $625.00 | |
| BATPDC12200 | D/Cyc 12V 215A AGM | $705.00 | |
| BATPDC12250 | D/Cyc 12v 268A AGM | $807.09 | |
Ritar Sealed AGM Deep Cycle Batteries
China Ritar Power is a Sealed Lead Acid (SLA) Battery Company listed in NASDAQ. Established in May 2002, Ritar manufactures and sells environmentally friendly Sealed Lead Acid (SLA) batteries.
Ritar power is a high-tech enterprise headquartered in Nanshan District, Shenzhen, China and has a manufacturing base in Fuyong town, Shenzhen and a new industrial park in Hengyang, Hunan Province. With 23 production lines, products10 series more than 500 types of products. Hengyang adjoins Zhuzhou smelter and Shuikoushan-- the Capital of Lead, has an extensive non-ferrous metal resource to achieve the gathering of the industrial chain, annual delivery capacity reached 9 million KVAH.
Ritar adhered to introduce and develop advanced technologies and processes, had set up Ritar Research Center, including 2 professors who have experience over 40 years in battery research, and over 50 research engineers. Adopted the world's most advanced production equipments and testing methods. Battery products have a long service life, high energy, Cadmium-free environmental protection and other features, also have got dozens of independent intellectual property rights of the patent invention. Ritar products are exported to more than 200 countries and regions all over the world. Ritar batteries are applied in light electric vehicles (LEVs), uninterruptible power supply (UPS) systems, electricity and telecommunications backup power systems, automatic control, wind and solar power systems.
Ritar RA Series 12-Volt AGM Deep Cycle Batteries
Ritar RA Series is a general purpose battery with 12 years design life in float service. It meets with IEC, JIS and BS standards. With up-dated AGM valve regulated technology and high purity raw materials, the RA series battery maintains high consistency for better performance and reliable standby service life.
Typical applications include: weekend or holiday homes with large electrical loads, medium solar systems for industrial applications, small solar and wind-driven power plants, offshore buoys, yachts, measurement stations.
Ritar Batteries are manufactured in China, Taiwan & Vietnam and covered by a 12 month warranty
Applications:
- Mobility Scooters
- Electric Bikes
- Caravans
- Marine
- Camping
Model |
Nominal Voltage V |
Rated Capacity (AH) 20-hr |
Rated Capacity (AH) 10-hr |
Length mm |
Width mm |
Height mm |
Ht. Over Terminal mm |
Weight kgs |
|---|---|---|---|---|---|---|---|---|
RT12240EV |
12 |
24.0 |
20.6 |
181 |
77 |
170 |
170 |
7.0 |
RT12260EV |
12 |
26.0 |
25.4 |
166 |
175 |
125 |
125 |
8.8 |
RA12-33EV |
12 |
33.0 |
31.4 |
196 |
130 |
163 |
180 |
10.2 |
RA12-45EV |
12 |
45.0 |
42.8 |
198 |
166 |
169 |
171 |
14.6 |
RA12-55D |
12 |
58.2 |
55.0 |
229 |
138 |
210 |
235 |
18.0 |
RA12-75D |
12 |
79.4 |
76.8 |
260 |
169 |
210 |
235 |
23.5 |
RA12-100SD |
12 |
100.8 |
97.9 |
307 |
169 |
210 |
235 |
29.0 |
RA12-120SD |
12 |
125.8 |
120.00 |
328 |
172 |
222 |
222 |
32.0 |
RA12-150D |
12 |
158.6 |
154.0 |
483 |
170 |
241 |
241 |
44.5 |
RA12-200D |
12 |
212.0 |
205.0 |
522 |
240 |
219 |
224 |
60.0 |
RA12-260D |
12 |
274.0 |
260.0 |
520 |
268 |
220 |
225 |
74.0 |
RA12-260 |
12 |
274.0 |
260.0 |
520 |
268 |
220 |
225 |
74.0 |
*OTHER AMPERAGES MAY BE AVAILABLE UPON REQUEST
| Ritar RA Series AGM Deep-Cycle Batteries | |||
| BATE12-12 | AGM 12V 12Ah EV | $65.00 | |
| BATE1224EV | Ritar 12V 24AH D/C | $135.00 | |
| BATE1226EV | Ritar 12V 26AH D/C | $106.76 | |
| BATE1233EV | Ritar 12V 33Ah AGM | $175.00 | |
| BATE1245EV | Ritar 12V 45AH D/C | $196.22 | |
| BATE1255D | Ritar 12V 55AH D/C | $267.02 | |
| BATE1275 | Ritar 12V 75AH D/C | $290.01 | |
| BATE12100SD | Ritar 12V 100AH DC | $350.00 | |
| BATE12120SD | Ritar 12V 120AH DC | $397.23 | |
| BATE12150D | RITAR 12V 150Ah D/C | $625.07 | |
| BATE12200D | Ritar 12V 214Ah D/C | $705.00 | |
| BATE12260D | Ritar 12V 274AH D/C | $920.00 | |
*Specs are subject to change without notice
PowerSonic PS Series 6-Volt & 12-Volt General Purpose AGM Batteries
The Power-Sonic PS Series have been evaluated and verified by CSIRO as conforming with the relevant requirements of the following criteria:
Australian Standard AS 1603.4 Appendix G-1987, ‘Automatic fire detection and alarm systems – Control and indicating equipment’.
The Power-Sonic PS Series batteries are approved by CSIRO for use in fire control and indicating equipment and are listed at ActivFire® Register of Fire Protection Equipment (Certificate No afp-2285).
Designed for general purpose standby and light cyclic applications, the Power-Sonic PS range is a great economical option. Featuring all of the excellent Power-Sonic characteristics outlined in the overview, they have been designed as a low lost alternative.
PowerSonic Batteries are designed in America and manufactured in China, Taiwan & Vietnam and covered by a 12 month warranty.
Features:
- 5 year design life
- Large number of cycles depending on average depth of discharge
- Rugged plastic case and cover
- Wide range of sizes from 2V 300mAh to 12V 140Ah
- Approved for transport by air. D.O.T., I.A.T.A. and F.A.A. certified.
Applications
- Standby Applications
- UPS
- Generators
- Fire & Security
- Medical
Model |
Nominal Voltage V |
Rated Capacity (AH) 20-hr |
Rated Capacity (AH) 5-hr |
Length mm |
Width mm |
Height mm |
Ht. Over Terminal mm |
Weight kgs |
Terminal Type Standard |
|---|---|---|---|---|---|---|---|---|---|
PS - 640 |
6 |
4.4 |
4.1 |
70 |
47 |
100 |
108 |
0.7 |
F1 |
PS - 1250 |
12 |
5.0 |
4.5 |
90 |
70 |
101 |
107 |
1.6 |
F1 |
PS - 1270 |
12 |
7.0 |
6.5 |
151 |
65 |
94 |
98 |
2.2 |
F1 |
*OTHER AMPERAGES MAY BE AVAILABLE UPON REQUEST
| PowerSonic 6V AGM Standby / General Purpose Batteries | |||
| BATPS64 | PS-640 6V 4.5Ah AGM | $24.99 | |
| PowerSonic 12V AGM Standby / General Purpose Batteries | |||
| BATPS125 | PS-1250F1 12V 5Ah AGM | $39.99 | |
| BATPS127 | PS-1270F1 12V 7Ah AGM | $39.99 | |
*Specs are subject to change without notice
PowerSonic PS 2-Volt AGM Stand-Alone Solar Batteries
The PSS 2 Volt Solar series batteries have been designed for use in Cyclic, Standby, and Solar Applications. Typical applications include: weekend or holiday homes with large electrical loads, medium solar systems for industrial applications, stand-alone solar systems, small solar and wind-driven power plants, offshore buoys, yachts, measurement stations.
PowerSonic Batteries are designed in America and manufactured in China, Taiwan & Vietnam and covered by a 12 month warranty
PSS 2 Volt Solar Series Features:
- Good cycle life making it perfect for off grid and critical load back-up applications
- Lowest upfront investment – giving you the fastest ROI
- Wide capacity range (170Ah – 3500Ah) perfect for large capacity off-grid systems
- Absorbent Glass Mat (AGM) technology for superior performance
- Valve regulated, spill proof construction allows safe operation in any position
- Large number of cycles
- Enhanced overcharge endurance
- Excellent recovery from over discharge situations
- Lower acid density, increased electrolyte volume and greater distance between the plates help keep the battery at lower temperatures and improve plate grid life
- Rugged impact resistant ABS case and cover (UL94-HB)
- Certified for transport by air, D.O.T., I.A.T.A., F.A.A. and C.A.B.
Applications:
- Off grid solar energy storage
- Critical power back up for remote signalling / transmission or sub stations
Model |
Nominal Voltage V |
Rated Capacity (AH) 100-hr |
Rated Capacity (AH) 20-hr |
Rated Capacity (AH) 5-hr |
Length mm |
Width mm |
Height mm |
Ht. Over Terminal mm |
Weight kgs |
Terminal Type Standard |
|---|---|---|---|---|---|---|---|---|---|---|
PSS - 2V350 |
2 |
345.0 |
325.0 |
300.0 |
170 |
150 |
328 |
350 |
18.3 |
T11 |
PSS - 2V450 |
2 |
460.0 |
430.0 |
400.0 |
210 |
175 |
330 |
350 |
24.9 |
T11 |
PSS - 2V550 |
2 |
575.0 |
535.0 |
500.0 |
240 |
175 |
327.5 |
347.5 |
30 |
T11 |
PSS - 2V700 |
2 |
690.0 |
645.0 |
600.0 |
300 |
175 |
330 |
350 |
36.3 |
T11 |
PSS - 2V900 |
2 |
920.0 |
855.0 |
800.0 |
410 |
175 |
330 |
350 |
50.4 |
T11 |
PSS - 2V1100 |
2 |
1150.0 |
1070.0 |
1000.0 |
475 |
175 |
328 |
350 |
59 |
T11 |
PSS - 2V1350 |
2 |
1380.0 |
1285.0 |
1200.0 |
475 |
175 |
328 |
350 |
66.4 |
T11 |
PSS - 2V1700 |
2 |
1730.0 |
1605.0 |
1500.0 |
403 |
354 |
339 |
349 |
96 |
T11 |
PSS - 2V2300 |
2 |
2300.0 |
2100.0 |
2000.0 |
490 |
350 |
339 |
349 |
120.5 |
T11 |
*OTHER AMPERAGES MAY BE AVAILABLE UPON REQUEST
| PowerSonic PSS Series 2V AGM Deep Cycle Batteries | |||
| BATPSS2V350 | PSS 2V 350A Solar | $258.00 | |
| BATPSS2V450 | PSS 2V 450A Solar | $331.00 | |
| BATPSS2V550 | PSS 2V 550A Solar | $390.00 | |
| BATPSS2V700 | PSS 2V 700A Solar | $465.00 | |
| BATPSS2V900 | PSS 2V 900A Solar | $645.00 | |
| BATPSS2V1100 | PSS 2V 1100A Sola | $837.00 | |
| BATPSS2V1350 | PSS 2V 1380A Sola | $912.00 | |
| BATPSS2V1700 | PSS 2V 1730A Sola | $1220.00 | |
| BATPSS2V2300 | PSS 2V 2300A Sola | $1576.00 | |
*Specs are subject to change without notice
The following batteries are order in
Enerdrive B-TEC LiFeP04 Lithium Batteries
In recent times Enerdrive has embarked on its own manufacturing program. They saw the need to control their own destiny and produce high-end products that the Australian market place was demanding.
This program has led to Enerdrive manufacturing its own range of ePOWER AC battery chargers & DC2DC battery chargers, alongside Lithium battery systems.
This product range is engineered to withstand the demanding applications in marine & mobile electrical systems.
Enerdrive B-TEC LiFeP04 12v 100Ah Slimline Lithium Battery
Enerdrive B-TEC LiFeP04 12v 100Ah Slimline Lithium Battery
Available in 12v 100Ah, 125Ah, 200Ah and 300Ah capacities and 24v 100Ah & 36v 100Ah, the ePOWER B-TEC lithium battery is designed and intended for use in deep cycle applications where a single battery is required that meets the amp hour capacity.
The Enerdrive B-TEC battery provides 60% more usable power than its equivalent lead acid cousin and being nearly 50% lighter and 30% smaller makes for a superior alternative.
The Enerdrive B-TEC Slimline battery is perfect for camper trailers, 4WD's (AUX battery), caravans, small water craft, low power communication sites or any other application that requires the use of a single deep cycle battery that meets the amp hour capacity.
With over 7 years of researching, designing and testing lithium batteries and the associated charging systems, Enerdrive are at the forefront of lithium battery systems in Australia. Enerdrive are the only Australian company that can supply a fully integrated self-branded energy system to suit your setup.
With over 3000 complete systems in operation Australia wide, Enerdrive is regarded as the leader in the field of lithium batteries and energy systems for Mobile, Marine and Remote applications.
Battery Management System
The 100Ah Slimline battery is able to accept a maximum inverter capacity of 1000W only. Exceeding the maximum inverter capacity can damage the BMS Management within the battery.
The battery is also equipped with an internal Battery Management System that can monitor and optimise each Prismatic cell within the battery during normal operation. It will protect the battery pack from over charge, over discharge, over temperature & short circuit. The BMS helps to ensure safe and accurate operation of the battery.
Model |
EPL-100BT-12V-SLIM |
|---|---|
Nominal Voltage |
12.8V |
Nominal Capacity |
100Ah |
Cycle Life (DOD - 80% under controlled conditions) |
> 2000 Cycles |
Standard Charge Specification (Lithium profile charger required) |
|
Battery Charge Temperature |
0 - 45°C |
Normal Charge Voltage CV/CC* |
14.20 - 14.60V |
Standby (Float) Voltage |
13.50 - 13.80V |
Maximum Charge Current |
80A @ 25°C for 30mins |
Recommended Charge Current |
20 - 50A (For Maximum Life, Charge in the lower amperage range) |
Standard Discharge Specification |
|
Battery Discharge Temperature |
-20 to -60°C |
Battery Output Voltage Range |
11.00 - 14.60V |
Maximum Discharge/Pulse Current |
100A @ 25°C ±5°C for 30 mins |
Pulse Discharge Current |
250A for 1.0s |
Discharge Cut-off Voltage |
< 11.20V |
Circuit Protection |
The battery is supplied with a LiFePO4 Battery Management System BMS that can monitor and optimize each single prismatic cell during charge & discharge, to protect the battery pack from overcharge, over discharge & short circuit. Overall, the BMS helps to ensure safe and accurate operation of the battery. |
Over-Charge Protection |
|
Over-charge Protection Per Cell |
3.90V ± 0.03V |
Over-charge Release Per Cell |
3.60V ± 0.05V |
Over-charge Release Method |
Discharge below release voltage |
Over-Discharge Protection |
|
Over-discharge Protection Per Cell |
2.80V ± 0.05V |
Over-discharge Release Per Cell |
3.20V ± 0.05V |
Over-discharge Release Method |
Apply Charge/Voltage > 12.8V |
Battery Manual Reset Button |
No |
Over Current Protection |
|
Discharge Over Current |
110A for 30s - 450A for 1s |
Protection Reset Time |
Approx 10s Auto Release |
Over Current Release Method |
Disconnect Load |
Over Temperature Protection |
|
Battery Discharge Over Temperature |
Protection to 65°C ± 5°C Release at 50°C ± 5°C |
Battery Charge Over Temperature |
Protection to 55°C ± 5°C Release at 45°C ± 5°C |
Short Circuit Protection |
Auto release after 5s |
Temperature & Humidity Range |
< 30 days -20°C | 60°C |5 - 75% RH > 90 days -10°C | 45°C |5 - 75% RH |
Self-discharge Rate |
< 3% Per Month |
Dimensions (L x W x H) |
551 x 110 x 240mm |
Weight |
Approx. 12.5KG |
Please note B-TEC batteries must not be installed:
- In vehicle engine bays or in high heat environments, refer to Section 10 - Battery Specifications of the manual.
- In wet areas such as caravan chassis mounts, open ute trays or boat deck areas.
- Inside compartments dedicated to carrying gas.
| Enerdrive B-TEC LiFeP04 12v 100Ah Slimline Lithium Battery | |||
| EPL-100BT-12V-SLIM | BTEC 100A | $1345.00 | |
Enerdrive B-TEC LiFeP04 12v 125Ah G2 Lithium Battery
Enerdrive B-TEC LiFeP04 12v 125Ah G2 Lithium Battery
Available in 12v 100Ah, 125Ah, 200Ah and 300Ah capacities and 24v 100Ah & 36v 100Ah, the ePOWER B-TEC lithium battery is designed and intended for use in deep cycle applications where a single battery is required that meets the amp hour capacity.
The Enerdrive B-TEC battery provides 60% more usable power than its equivalent lead acid cousin and being nearly 50% lighter and 30% smaller makes for a superior alternative.
The G2 now incorporates a “Built-In Reset Button” making re-starting a flat battery a breeze. No longer do you need to apply a voltage to the battery terminals to wake up the battery. Press the button and within seconds, the battery will come back to life ready to accept a charge source to rejuvenate the battery.
The Enerdrive B-TEC battery is perfect for camper trailers, 4WD's (AUX battery), caravans, small water craft, low power communication sites or any other application that requires the use of a single deep cycle battery that meets the amp hour capacity.
With over 8 years of researching, designing and testing lithium batteries and the associated charging systems, Enerdrive are at the forefront of lithium battery systems in Australia. Enerdrive are the only Australian company that can supply a fully integrated self-branded energy system to suit your setup.
With over 4000 complete systems in operation Australia wide, Enerdrive is regarded as the leader in the field of lithium batteries and energy systems for Mobile, Marine and Remote applications.
Battery Management System
The 125Ah G2 battery is able to accept a maximum inverter capacity of 1000W only. Exceeding the maximum inverter capacity can damage the BMS Management within the battery.
The battery is also equipped with an internal Battery Management System that can monitor and optimise each Prismatic cell within the battery during normal operation. It will protect the battery pack from over charge, over discharge, over temperature & short circuit. The BMS helps to ensure safe and accurate operation of the battery.
Model |
EPL-125BT-12V G2 |
|---|---|
Nominal Voltage |
12.8V |
Nominal Capacity |
125Ah |
Cycle Life (DOD - 80% under controlled conditions) |
> 2000 Cycles |
Standard Charge Specification (Lithium profile charger required) |
|
Battery Charge Temperature |
0 - 45°C |
Normal Charge Voltage CV/CC* |
14.20 - 14.60V |
Standby (Float) Voltage |
13.50 - 13.80V |
Maximum Charge Current |
60A @ 25°C for 30mins |
Recommended Charge Current |
20 - 60A (For Maximum Life, Charge in the lower amperage range) |
Standard Discharge Specification |
|
Battery Discharge Temperature |
-20 to -60°C |
Battery Output Voltage Range |
11.00 - 14.60V |
Maximum Discharge/Pulse Current |
100A @ 25°C ±5°C for 30 mins |
Pulse Discharge Current |
450A for 1.0s |
Discharge Cut-off Voltage |
< 11.20V |
Circuit Protection |
The battery is supplied with a LiFePO4 Battery Management System BMS that can monitor and optimize each single prismatic cell during charge & discharge, to protect the battery pack from overcharge, over discharge & short circuit. Overall, the BMS helps to ensure safe and accurate operation of the battery. |
Over-Charge Protection |
|
Over-charge Protection Per Cell |
3.90V ± 0.03V |
Over-charge Release Per Cell |
3.60V ± 0.05V |
Over-charge Release Method |
Discharge below release voltage |
Over-Discharge Protection |
|
Over-discharge Protection Per Cell |
2.80V ± 0.05V |
Over-discharge Release Per Cell |
3.20V ± 0.05V |
Over-discharge Release Method |
Apply Charge/Voltage > 12.8V |
Battery Manual Reset Button |
Yes |
Over Current Protection |
|
Discharge Over Current |
110A for 30s - 450A for 1s |
Protection Reset Time |
Approx 10s Auto Release |
Over Current Release Method |
Disconnect Load |
Over Temperature Protection |
|
Battery Discharge Over Temperature |
Protection to 65°C ± 5°C Release at 50°C ± 5°C |
Battery Charge Over Temperature |
Protection to 55°C ± 5°C Release at 45°C ± 5°C |
Short Circuit Protection |
Auto release after 5s |
Temperature & Humidity Range |
< 30 days -20°C | 60°C |5 - 75% RH > 90 days -10°C | 45°C |5 - 75% RH |
Self-discharge Rate |
< 3% Per Month |
Dimensions (L x W x H) |
318 x 165 x 232mm |
Weight |
Approx. 15.5KG |
Please note B-TEC batteries must not be installed:
- In vehicle engine bays or in high heat environments, refer to Section 10 - Battery Specifications of the manual.
- In wet areas such as caravan chassis mounts, open ute trays or boat deck areas.
- Inside compartments dedicated to carrying gas.
| Enerdrive B-TEC LiFeP04 12v 125Ah G2 Lithium Battery | |||
| EPL-125BT-12V | BTEC 12v 125A | $1499.00 | |
Enerdrive B-TEC LiFeP04 12v 200Ah G2 Lithium Battery
Enerdrive B-TEC LiFeP04 12v 200Ah G2 Lithium Battery
Available in 12v 100Ah, 125Ah, 200Ah and 300Ah capacities and 24v 100Ah & 36v 100Ah, the ePOWER B-TEC lithium battery is designed and intended for use in deep cycle applications where a single battery is required that meets the amp hour capacity.
The Enerdrive B-TEC G2 battery provides 60% more usable power than its equivalent lead acid cousin and being nearly 50% lighter and 30% smaller makes for a superior alternative.
The Enerdrive B-TEC G2 battery is perfect for camper trailers, 4WD's (AUX battery), caravans, small water craft, low power communication sites or any other application that requires the use of a single deep cycle battery that meets the amp hour capacity.
The New Generation 2 B-TEC
So, How does the New Enerdrive Generation 2 (G2) B-TEC 200Ah Lithium Battery measure up against it original predecessor? Let's have a look.
Model |
Original |
Generation 2 |
|---|---|---|
Length |
485mm |
505mm |
Width |
170mm |
172.5mm |
Height |
245mm |
265mm |
Also included for free is a metal battery tray and hold down strap to complete the installation process
The G2 now incorporates a “Built-In Reset Button” making re-starting a flat battery a breeze. No longer do you need to apply a voltage to the battery terminals to wake up the battery. Press the button and within seconds, the battery will come back to life ready to accept a charge source to rejuvenate the battery.
The new G2 also includes a RS485 communications port located on the top of the battery. This port allows for integration onto other CanBus systems for data monitoring and recording.
The New Enerdrive Generation 2 (G2) B-TEC 200Ah Lithium Battery now comes with a 5 year warranty, giving you peace of mind that this product will keep you covered.
With over 8 years of researching, designing and testing lithium batteries and the associated charging systems, Enerdrive are at the forefront of lithium battery systems in Australia. Enerdrive are the only Australian company that can supply a fully integrated self-branded energy system to suit your setup.
With over 4000 complete systems in operation Australia wide, Enerdrive is regarded as the leader in the field of lithium batteries and energy systems for Mobile, Marine and Remote applications.
Battery Management System
The G2 200Ah battery is able to accept a maximum inverter capacity of 2600W only. Exceeding the maximum inverter capacity can damage the BMS Management within the battery.
The battery is also equipped with an internal Battery Management System that can monitor and optimise each Prismatic cell within the battery during normal operation. It will protect the battery pack from over charge, over discharge, over temperature & short circuit. The BMS helps to ensure safe and accurate operation of the battery.
Model |
EPL-200BT-12V G2 |
|---|---|
Nominal Voltage |
12.8V |
Nominal Capacity |
200Ah |
Cycle Life (DOD - 80% under controlled conditions) |
> 2000 Cycles |
Standard Charge Specification (Lithium profile charger required) |
|
Battery Charge Temperature |
0 - 45°C |
Normal Charge Voltage CV/CC* |
14.20 - 14.60V |
Standby (Float) Voltage |
13.50 - 13.80V |
Maximum Charge Current |
150A @ 25°C for 30mins |
Recommended Charge Current |
40 - 100A (For Maximum Life, Charge in the lower amperage range) |
Standard Discharge Specification |
|
Battery Discharge Temperature |
-20 to -60°C |
Battery Output Voltage Range |
11.00 - 14.60V |
Maximum Discharge/Pulse Current |
200A @ 25°C ±5°C for 30 mins |
Pulse Discharge Current |
450A for 1.0s |
Discharge Cut-off Voltage |
< 11.20V |
Circuit Protection |
The battery is supplied with a LiFePO4 Battery Management System BMS that can monitor and optimize each single prismatic cell during charge & discharge, to protect the battery pack from overcharge, over discharge & short circuit. Overall, the BMS helps to ensure safe and accurate operation of the battery. |
Over-Charge Protection |
|
Over-charge Protection Per Cell |
3.90V ± 0.03V |
Over-charge Release Per Cell |
3.60V ± 0.05V |
Over-charge Release Method |
Discharge below release voltage |
Over-Discharge Protection |
|
Over-discharge Protection Per Cell |
2.80V ± 0.05V |
Over-discharge Release Per Cell |
3.20V ± 0.05V |
Over-discharge Release Method |
Apply Charge/Voltage > 12.8V |
Battery Manual Reset Button |
Yes |
Over Current Protection |
|
Discharge Over Current |
220A for 30s - 450A for 1s |
Protection Reset Time |
Approx 10s Auto Release |
Over Current Release Method |
Disconnect Load |
Over Temperature Protection |
|
Battery Discharge Over Temperature |
Protection to 65°C ± 5°C Release at 50°C ± 5°C |
Battery Charge Over Temperature |
Protection to 55°C ± 5°C Release at 45°C ± 5°C |
Short Circuit Protection |
Auto release after 5s |
Temperature & Humidity Range |
< 30 days -20°C | 60°C |5 - 75% RH > 90 days -10°C | 45°C |5 - 75% RH |
Self-discharge Rate |
< 3% Per Month |
Dimensions (L x W x H) |
505 x 172 x 265mm |
Weight |
Approx. 25KG |
Please note B-TEC batteries must not be installed:
- In vehicle engine bays or in high heat environments, refer to Section 10 - Battery Specifications of the manual.
- In wet areas such as caravan chassis mounts, open ute trays or boat deck areas.
- Inside compartments dedicated to carrying gas.
| Enerdrive B-TEC LiFeP04 12v 200Ah G2 Lithium Battery | |||
| EPL-200BT-12V-G2 | BTEC 12v 200A | $2399.00 | |
Enerdrive B-TEC LiFeP04 12v 300Ah G2 Lithium Battery
Enerdrive B-TEC LiFeP04 12v 300Ah G2 Lithium Battery
Available in 12v 100Ah, 125Ah, 200Ah and 300Ah capacities and 24v 100Ah & 36v 100Ah, the ePOWER B-TEC lithium battery is designed and intended for use in deep cycle applications where a single battery is required that meets the amp hour capacity.
The Enerdrive B-TEC G2 battery provides 60% more usable power than its equivalent lead acid cousin and being nearly 50% lighter and 30% smaller makes for a superior alternative.
The Enerdrive B-TEC G2 battery is perfect for camper trailers, 4WD's (AUX battery), caravans, small water craft, low power communication sites or any other application that requires the use of a single deep cycle battery that meets the amp hour capacity.
The New Generation 2 B-TEC
So, How does the New Enerdrive Generation 2 (G2) B-TEC 300Ah Lithium Battery measure up against it original predecessor? Let's have a look.
Model |
Original |
Generation 2 |
|---|---|---|
Length |
519mm |
521mm |
Width |
273mm |
280mm |
Height |
222mm |
253mm |
Also included for free is a metal battery tray and hold down strap to complete the installation process.
The G2 now incorporates a “Built-In Reset Button” making re-starting a flat battery a breeze. No longer do you need to apply a voltage to the battery terminals to wake up the battery. Press the button and within seconds, the battery will come back to life ready to accept a charge source to rejuvenate the battery.
The new G2 also includes a RS485 communications port located on the top of the battery. This port allows for integration onto other CanBus systems for data monitoring and recording.
The New Enerdrive Generation 2 (G2) B-TEC 300Ah Lithium Battery now comes with a 5 year warranty, giving you peace of mind that this product will keep you covered.
With over 8 years of researching, designing and testing lithium batteries and the associated charging systems, Enerdrive are at the forefront of lithium battery systems in Australia. Enerdrive are the only Australian company that can supply a fully integrated self-branded energy system to suit your setup.
With over 4000 complete systems in operation Australia wide, Enerdrive is regarded as the leader in the field of lithium batteries and energy systems for Mobile, Marine and Remote applications.
Battery Management System
The G2 300Ah battery is able to accept a maximum inverter capacity of 3000W only. Exceeding the maximum inverter capacity can damage the BMS Management within the battery.
The battery is also equipped with an internal Battery Management System that can monitor and optimise each Prismatic cell within the battery during normal operation. It will protect the battery pack from over charge, over discharge, over temperature & short circuit. The BMS helps to ensure safe and accurate operation of the battery.
Model |
EPL-300BT-12V G2 |
|---|---|
Nominal Voltage |
12.8V |
Nominal Capacity |
300Ah |
Cycle Life (DOD - 80% under controlled conditions) |
> 2000 Cycles |
Standard Charge Specification (Lithium profile charger required) |
|
Battery Charge Temperature |
0 - 45°C |
Normal Charge Voltage CV/CC* |
14.20 - 14.60V |
Standby (Float) Voltage |
13.50 - 13.80V |
Maximum Charge Current |
190A @ 25°C for 30mins |
Recommended Charge Current |
80 - 120A (For Maximum Life, Charge in the lower amperage range) |
Standard Discharge Specification |
|
Battery Discharge Temperature |
-20 to -60°C |
Battery Output Voltage Range |
11.00 - 14.60V |
Maximum Discharge/Pulse Current |
250A @ 25°C ±5°C for 30 mins |
Pulse Discharge Current |
450A for 1.0s |
Discharge Cut-off Voltage |
< 11.20V |
Circuit Protection |
The battery is supplied with a LiFePO4 Battery Management System BMS that can monitor and optimize each single prismatic cell during charge & discharge, to protect the battery pack from overcharge, over discharge & short circuit. Overall, the BMS helps to ensure safe and accurate operation of the battery. |
Over-Charge Protection |
|
Over-charge Protection Per Cell |
3.90V ± 0.03V |
Over-charge Release Per Cell |
3.60V ± 0.05V |
Over-charge Release Method |
Discharge below release voltage |
Over-Discharge Protection |
|
Over-discharge Protection Per Cell |
2.80V ± 0.05V |
Over-discharge Release Per Cell |
3.20V ± 0.05V |
Over-discharge Release Method |
Apply Charge/Voltage > 12.8V |
Battery Manual Reset Button |
Yes |
Over Current Protection |
|
Discharge Over Current |
280A for 25s - 450A for 3.5s |
Protection Reset Time |
Approx 10s Auto Release |
Over Current Release Method |
Disconnect Load |
Over Temperature Protection |
|
Battery Discharge Over Temperature |
Protection to 65°C ± 5°C Release at 50°C ± 5°C |
Battery Charge Over Temperature |
Protection to 55°C ± 5°C Release at 45°C ± 5°C |
Short Circuit Protection |
Auto release after 5s |
Temperature & Humidity Range |
< 30 days -20°C | 60°C |5 - 75% RH > 90 days -10°C | 45°C |5 - 75% RH |
Self-discharge Rate |
< 3% Per Month |
Dimensions (L x W x H) |
505 x 172 x 265mm |
Weight |
Approx. 25KG |
Please note B-TEC batteries must not be installed:
- In vehicle engine bays or in high heat environments, refer to Section 10 - Battery Specifications of the manual.
- In wet areas such as caravan chassis mounts, open ute trays or boat deck areas.
- Inside compartments dedicated to carrying gas.
| Enerdrive B-TEC LiFeP04 12v 300Ah G2 Lithium Battery | |||
| EPL-300BT-12V-G2 | BTEC 12v 300A | $3750.00 | |
DryPower LiFeP04 Lithium Batteries
Drypower is more than a brand. Drypower takes existing battery technology and improves on it to provide smart battery solutions to meet both performance and budgetary criteria.
Within the Drypower stable is a family of AGM and GEL type sealed lead acid batteries made to a premium standard using Taiwanese technology of a higher grade than the mainly Chinese produced competition.
In 2015 after several years of research and development, Drypower augmented its existing product line-up with a new range of lithium iron phosphate batteries that are first and foremost safe, reliable and provide long-term value to users. Inside every battery is an advanced battery management system featuring multiple safety protocols the no quality Lithium rechargeable battery should be without.
Backed by decades of experience by the leaders in rechargeable industrial battery technology, Drypower brings a new standard of batteries that are already satisfying the high performance requirements of major clients both in private and Government sectors across Australia and New Zealand.
Drypower 12LFP100PS 12V Rechargeable Lithium Deep Cycle Battery
High power 12.8V 100Ah lithium iron phosphate (LiFePO4) rechargeable battery
Rechargeable Lithium LiFePO4 high power modules to handle anything SLA can. Get 100% capacity utilisation at less than half the weight.
Advanced battery technology for cyclic and motive power applications such as mobility, recreational caravan & RV, marine, medical equipment, solar applications and more.
- Deep cycle power rechargeable lithium batteries with over 2000 cycles to 100% DoD in industrial or high drain applications.
- All the power without the bulky weight of Lead Acid battery equivalents.
- High rate discharge capable and superior total capacity utilisation (up to 100% DoD) with a flat discharge curve for strong, consistent power delivery.
- Low self discharge and long storage life with no risk of sulphation.
- Integrated layers of safety to IEC62133-2:2017 and UN38.3 standards at the cell level as well as BMS level protection against over charge, over voltage, under voltage and over temperature. Enclosed in IP5x/IP6x rated protective case for better durability in harsh environments.
Long Service Life & Reliability
>2000 cycles @100% DoD (25°C) to 80% of original capacity - longer service life than SLA to reduce maintenance costs.
High Energy Density - More Power Wh/kg
Higher total system capacity and superior utilisation (full 100% DoD) to reduce overall system size and footprint.
Robust Enclosure
Enclosed in IP5x (dust resistant) or IP6x (dust tight) case with closed loop terminals - suitable for harsh environments.
Stable Chemistry & Built-in Circuit Protection
IEC & UN38.3 Safety Certified at cell level and integrated BMS protection to ensure safety and prevent damage.
Lightweight
Approx. 1/2 the weight (or less) of equivalent in SLA means lower logistics costs and minimal OH&S concerns.
Superior Charge & Discharge Efficiency
Faster charge/discharge rates (C/2 LiFePO4 vs C/20 SLA) for higher power usage and less downtime when charging.
Wide Operating Temperature Tolerance
Suitable for use in a wider range of applications where ambient temperature is atypical: from 20°C up to +60°C.
Better Shelf Life
Storage is not a problem thanks to extremely low self discharge (LSD) and no risk of sulphation.
Fully Recyclable Battery
An environmentally friendly battery option, with no lead or calcium that can leak into the enviroment.
Battery Management System
All Drypower Rechargeable Lithium batteries adhere to strict safety guidelines by incorporating Battery Management Systems (BMS) into each battery.
The BMS comprises different protection components:
- Integrated Circuit (IC)
- MOSFET - compact transistor
- Fuse - protects against excessive current
- Thermistor - temperature sensor
- Protection Circuit Module (PCM)
The inclusion of a BMS helps to:
- Maintain safety for users.
- Prevent damage to equipment and property.
- Eliminate concerns about use of the wrong charger for this chemistry type.
- Minimise the risk of overdischarge causing damage.
- Provide short circuit and overcharge protection.
- The BMS ensures optimal operating conditions for your battery to last longer and perform at its best in your devices and equipment
Model |
12LFP100PS |
|---|---|
Nominal Voltage |
12.8V |
Nominal Capacity |
100Ah (1280Wh) |
Cycle Life (DOD - 80% under controlled conditions) |
>2000 cycles (100% DoD) >3000 cycles (80% DoD) >4000 cycles (50% DoD) |
Maximum Charge Current |
100A (1C) |
Recommended Charge Current |
20A (0.2C) |
Battery Charge Temperature |
-0 to -45°C |
Maximum Discharge Current |
100A (1C) |
Recommended Discharge Current |
20A (0.2C) |
Battery Discharge Temperature |
-20 to -60°C |
Cell Used |
IFP23140160 |
Assembly |
4S2P-Pris |
Operating Humidity Range |
5% to 85% |
Case Material |
ABS |
Termination |
F18 (M8 Bolt) |
Ingress Protection Rating |
IP64 |
Series Connection |
Up to 4S |
Parallel Connection |
No |
Dimensions (L x W x H) |
329 x 171 x 217mm (225mm with Terminals) |
Weight |
Approx. 11.4KG |
| Drypower 12LFP100PS LiFeP04 12v 100Ah Lithium Battery | |||
| BATDP12100 |  |
||
Drypower 12LFP150PS 12V Rechargeable Lithium Deep Cycle Battery
High power 12.8V 150Ah lithium iron phosphate (LiFePO4) rechargeable battery
Rechargeable Lithium LiFePO4 high power modules to handle anything SLA can. Get 100% capacity utilisation at less than half the weight.
Advanced battery technology for cyclic and motive power applications such as mobility, recreational caravan & RV, marine, medical equipment, solar applications and more.
- Deep cycle power rechargeable lithium batteries with over 2000 cycles to 100% DoD in industrial or high drain applications.
- All the power without the bulky weight of Lead Acid battery equivalents.
- High rate discharge capable and superior total capacity utilisation (up to 100% DoD) with a flat discharge curve for strong, consistent power delivery.
- Low self discharge and long storage life with no risk of sulphation.
- Integrated layers of safety to IEC62133-2:2017 and UN38.3 standards at the cell level as well as BMS level protection against over charge, over voltage, under voltage and over temperature. Enclosed in IP5x/IP6x rated protective case for better durability in harsh environments.
Long Service Life & Reliability
>2000 cycles @100% DoD (25°C) to 80% of original capacity - longer service life than SLA to reduce maintenance costs.
High Energy Density - More Power Wh/kg
Higher total system capacity and superior utilisation (full 100% DoD) to reduce overall system size and footprint.
Robust Enclosure
Enclosed in IP5x (dust resistant) or IP6x (dust tight) case with closed loop terminals - suitable for harsh environments.
Stable Chemistry & Built-in Circuit Protection
IEC & UN38.3 Safety Certified at cell level and integrated BMS protection to ensure safety and prevent damage.
Lightweight
Approx. 1/2 the weight (or less) of equivalent in SLA means lower logistics costs and minimal OH&S concerns.
Superior Charge & Discharge Efficiency
Faster charge/discharge rates (C/2 LiFePO4 vs C/20 SLA) for higher power usage and less downtime when charging.
Wide Operating Temperature Tolerance
Suitable for use in a wider range of applications where ambient temperature is atypical: from 20°C up to +60°C.
Better Shelf Life
Storage is not a problem thanks to extremely low self discharge (LSD) and no risk of sulphation.
Fully Recyclable Battery
An environmentally friendly battery option, with no lead or calcium that can leak into the enviroment.
Battery Management System
All Drypower Rechargeable Lithium batteries adhere to strict safety guidelines by incorporating Battery Management Systems (BMS) into each battery.
The BMS comprises different protection components:
- Integrated Circuit (IC)
- MOSFET - compact transistor
- Fuse - protects against excessive current
- Thermistor - temperature sensor
- Protection Circuit Module (PCM)
The inclusion of a BMS helps to:
- Maintain safety for users.
- Prevent damage to equipment and property.
- Eliminate concerns about use of the wrong charger for this chemistry type.
- Minimise the risk of overdischarge causing damage.
- Provide short circuit and overcharge protection.
- The BMS ensures optimal operating conditions for your battery to last longer and perform at its best in your devices and equipment
Model |
12LFP150PS |
|---|---|
Nominal Voltage |
12.8V |
Nominal Capacity |
150Ah (1920Wh) |
Cycle Life (DOD - 80% under controlled conditions) |
>2000 cycles (100% DoD) >3000 cycles (80% DoD) >4000 cycles (50% DoD) |
Maximum Charge Current |
150A (1C) |
Recommended Charge Current |
30A (0.2C) |
Battery Charge Temperature |
-0 to -45°C |
Maximum Discharge Current |
150A (1C) |
Recommended Discharge Current |
30A (0.2C) |
Battery Discharge Temperature |
-20 to -60°C |
Cell Used |
IFP23140160 |
Assembly |
4S3P-Pris |
Operating Humidity Range |
5% to 85% |
Case Material |
ABS |
Termination |
F18 (M8 Bolt) |
Ingress Protection Rating |
IP64 |
Series Connection |
Up to 4S |
Parallel Connection |
No |
Dimensions (L x W x H) |
406 x 173 x 211mm (240mm with Terminals) |
Weight |
Approx. 16.6KG |
| Drypower 12LFP150PS LiFeP04 12v 150Ah Lithium Battery | |||
| BATDP12150 | |
||
Drypower 12LFP200P 12V Rechargeable Lithium Deep Cycle Battery
High power 12.8V 200Ah lithium iron phosphate (LiFePO4) rechargeable battery
Rechargeable Lithium LiFePO4 high power modules to handle anything SLA can. Get 100% capacity utilisation at less than half the weight.
Advanced battery technology for cyclic and motive power applications such as mobility, recreational caravan & RV, marine, medical equipment, solar applications and more.
- Deep cycle power rechargeable lithium batteries with over 2000 cycles to 100% DoD in industrial or high drain applications.
- All the power without the bulky weight of Lead Acid battery equivalents.
- High rate discharge capable and superior total capacity utilisation (up to 100% DoD) with a flat discharge curve for strong, consistent power delivery.
- Low self discharge and long storage life with no risk of sulphation.
- Integrated layers of safety to IEC62133-2:2017 and UN38.3 standards at the cell level as well as BMS level protection against over charge, over voltage, under voltage and over temperature. Enclosed in IP5x/IP6x rated protective case for better durability in harsh environments.
Long Service Life & Reliability
>2000 cycles @100% DoD (25°C) to 80% of original capacity - longer service life than SLA to reduce maintenance costs.
High Energy Density - More Power Wh/kg
Higher total system capacity and superior utilisation (full 100% DoD) to reduce overall system size and footprint.
Robust Enclosure
Enclosed in IP5x (dust resistant) or IP6x (dust tight) case with closed loop terminals - suitable for harsh environments.
Stable Chemistry & Built-in Circuit Protection
IEC & UN38.3 Safety Certified at cell level and integrated BMS protection to ensure safety and prevent damage.
Lightweight
Approx. 1/2 the weight (or less) of equivalent in SLA means lower logistics costs and minimal OH&S concerns.
Superior Charge & Discharge Efficiency
Faster charge/discharge rates (C/2 LiFePO4 vs C/20 SLA) for higher power usage and less downtime when charging.
Wide Operating Temperature Tolerance
Suitable for use in a wider range of applications where ambient temperature is atypical: from 20°C up to +60°C.
Better Shelf Life
Storage is not a problem thanks to extremely low self discharge (LSD) and no risk of sulphation.
Fully Recyclable Battery
An environmentally friendly battery option, with no lead or calcium that can leak into the enviroment.
Battery Management System
All Drypower Rechargeable Lithium batteries adhere to strict safety guidelines by incorporating Battery Management Systems (BMS) into each battery.
The BMS comprises different protection components:
- Integrated Circuit (IC)
- MOSFET - compact transistor
- Fuse - protects against excessive current
- Thermistor - temperature sensor
- Protection Circuit Module (PCM)
The inclusion of a BMS helps to:
- Maintain safety for users.
- Prevent damage to equipment and property.
- Eliminate concerns about use of the wrong charger for this chemistry type.
- Minimise the risk of overdischarge causing damage.
- Provide short circuit and overcharge protection.
- The BMS ensures optimal operating conditions for your battery to last longer and perform at its best in your devices and equipment
Model |
12LFP200PS |
|---|---|
Nominal Voltage |
12.8V |
Nominal Capacity |
200Ah (2560Wh) |
Cycle Life (DOD - 80% under controlled conditions) |
>2000 cycles (100% DoD) >3000 cycles (80% DoD) >4000 cycles (50% DoD) |
Maximum Charge Current |
150A (1C) |
Recommended Charge Current |
40A (0.2C) |
Battery Charge Temperature |
-0 to -45°C |
Maximum Discharge Current |
150A (1C) |
Recommended Discharge Current |
40A (0.2C) |
Battery Discharge Temperature |
-20 to -60°C |
Cell Used |
IFP23140160 |
Assembly |
4S4P-Pris |
Operating Humidity Range |
5% to 85% |
Case Material |
ABS |
Termination |
F18 (M8 Bolt) |
Ingress Protection Rating |
IP64 |
Series Connection |
Up to 4S |
Parallel Connection |
No |
Dimensions (L x W x H) |
490 x 170 x 240mm (240mm with Terminals) |
Weight |
Approx. 21.5KG |
| Drypower 12LFP200PS LiFeP04 12v 200Ah Lithium Battery | |||
| BATDP12200 | |
||
Drypower 12LFP300P 12V Rechargeable Lithium Deep Cycle Battery
High power 12.8V 300Ah lithium iron phosphate (LiFePO4) rechargeable battery
Rechargeable Lithium LiFePO4 high power modules to handle anything SLA can. Get 100% capacity utilisation at less than half the weight.
Advanced battery technology for cyclic and motive power applications such as mobility, recreational caravan & RV, marine, medical equipment, solar applications and more.
- Deep cycle power rechargeable lithium batteries with over 2000 cycles to 100% DoD in industrial or high drain applications.
- All the power without the bulky weight of Lead Acid battery equivalents.
- High rate discharge capable and superior total capacity utilisation (up to 100% DoD) with a flat discharge curve for strong, consistent power delivery.
- Low self discharge and long storage life with no risk of sulphation.
- Integrated layers of safety to IEC62133-2:2017 and UN38.3 standards at the cell level as well as BMS level protection against over charge, over voltage, under voltage and over temperature. Enclosed in IP5x/IP6x rated protective case for better durability in harsh environments.
Long Service Life & Reliability
>2000 cycles @100% DoD (25°C) to 80% of original capacity - longer service life than SLA to reduce maintenance costs.
High Energy Density - More Power Wh/kg
Higher total system capacity and superior utilisation (full 100% DoD) to reduce overall system size and footprint.
Robust Enclosure
Enclosed in IP5x (dust resistant) or IP6x (dust tight) case with closed loop terminals - suitable for harsh environments.
Stable Chemistry & Built-in Circuit Protection
IEC & UN38.3 Safety Certified at cell level and integrated BMS protection to ensure safety and prevent damage.
Lightweight
Approx. 1/2 the weight (or less) of equivalent in SLA means lower logistics costs and minimal OH&S concerns.
Superior Charge & Discharge Efficiency
Faster charge/discharge rates (C/2 LiFePO4 vs C/20 SLA) for higher power usage and less downtime when charging.
Wide Operating Temperature Tolerance
Suitable for use in a wider range of applications where ambient temperature is atypical: from 20°C up to +60°C.
Better Shelf Life
Storage is not a problem thanks to extremely low self discharge (LSD) and no risk of sulphation.
Fully Recyclable Battery
An environmentally friendly battery option, with no lead or calcium that can leak into the enviroment.
Battery Management System
All Drypower Rechargeable Lithium batteries adhere to strict safety guidelines by incorporating Battery Management Systems (BMS) into each battery.
The BMS comprises different protection components:
- Integrated Circuit (IC)
- MOSFET - compact transistor
- Fuse - protects against excessive current
- Thermistor - temperature sensor
- Protection Circuit Module (PCM)
The inclusion of a BMS helps to:
- Maintain safety for users.
- Prevent damage to equipment and property.
- Eliminate concerns about use of the wrong charger for this chemistry type.
- Minimise the risk of overdischarge causing damage.
- Provide short circuit and overcharge protection.
- The BMS ensures optimal operating conditions for your battery to last longer and perform at its best in your devices and equipment
Model |
12LFP300P |
|---|---|
Nominal Voltage |
12.8V |
Nominal Capacity |
300Ah (3840Wh) |
Cycle Life (DOD - 80% under controlled conditions) |
>2000 cycles (100% DoD) >3000 cycles (80% DoD) >4000 cycles (50% DoD) |
Maximum Charge Current |
200A (1C) |
Recommended Charge Current |
60A (0.2C) |
Battery Charge Temperature |
-0 to -45°C |
Maximum Discharge Current |
200A (1C) |
Recommended Discharge Current |
60A (0.2C) |
Battery Discharge Temperature |
-20 to -60°C |
Cell Used |
CB27173204EA-100Ah |
Assembly |
4S3P-Pris |
Operating Humidity Range |
5% to 85% |
Case Material |
ABS |
Termination |
F18 (M8 Bolt) |
Ingress Protection Rating |
IP64 |
Series Connection |
Up to 4S |
Parallel Connection |
No |
Dimensions (L x W x H) |
520 x 240 x 220mm (225mm with Terminals) |
Weight |
Approx. 30.5KG |
| Drypower 12LFP300P LiFeP04 12v 300Ah Lithium Battery | |||
| BATDP12300 | DRYPOWER 12V 300AH | $2799.00 | |
PylonTech LiFeP04 Lithium Batteries
Pylontech is a unique company with vertical integration of all technologies needed for ESS (Energy storage system) including cathode material, lithium cell, BMS and system integration. With self developed key technologies and dedication to ESS applications, Pylontech had been pioneering the global ESS market from 2013.
With more than 3.0 GWh products been commissioned in 80 countries until end 2019, Pylontech is proudly contributing our strength in changing the way people generating, transferring and using the electricity.
Pylontech RV12100 12.8V 100Ah 1280Wh 4S4P Lithium Iron Phosphate (LiFePO4) Battery
High power 12.8V 100Ah lithium iron phosphate (LiFePO4) rechargeable battery
Rechargeable Lithium LiFePO4 high power modules to handle anything SLA can. Get 100% capacity utilisation at less than half the weight.
Ideal for applications in Caravan, RV's and Marine power storage and as a drop in replacement for AGM/GEL Lead Acid Batteries. Fits in most N70 sized battery boxes (L 300mm x W 173mm x H 220mm)
Pylontech 12V Series All-purpose Lithium Ion Battery
The Pylontech RV12V Series are the newly developed all-purpose lithium ion battery module which can be used for energy storage as well as starting. With the cutting edge LFP (Lithium iron Phosphate) cell, embedded BMS (Battery Management System) and mechanical design, Pylontech RV12V Series products provides inherent safety, extreme high reliability and zero maintenance. Comparing to the same capacity lead-acid based batteries, it has more than twice of the usable capacity, more than 3 times of the life cycle, and only about 40% of the weight. It is a prefect replacement to the lead acid based batteries in the applications such as marine, RV, golf carts and solar storage. RV12V Series product will bring you the perfect experience in many applications.
Pylontech RV12100 Advantages
- Twice the usable capacity (compared to the same capacity of FLA/AGM/GEL)
- Deep Cycle (Auto cut-off at 10V)
- Calendar life of 10+ years, cycle life of 3000 times
- High charging current
- Embedded BMS
- Dual lug terminals
- Zero maintenance
- Working Temperature -20 to -60°C
- Rugged mechanical design
This product is certified to UN38.3
This battery has been tested & complies with the UN Model Regulation, Manual of Test & Criteria, Part III, Subsection 38.3
Model |
RV12100 |
|---|---|
Nominal Voltage |
12.8V |
Nominal Capacity |
100Ah (1280Wh) |
Cycle Life (DOD - 80% under controlled conditions) |
>3000 cycles (90% DoD) @ 25ºC |
Maximum Charge Voltage |
14.2V - 14.6V (14.4V recommended) |
Max. continuous charge current |
50A |
Max. continuous discharge current |
100A |
Discharge Cut-Off Voltage |
10V |
Operating Discharge temperature |
-15 to -50°C |
Operating Charge temperature |
-0 to -50°C |
Storage temperature |
-20 to -60°C |
State of Charge Display |
Yes |
Short Circuit Protection |
Yes |
IP Rating |
IP20 Rating |
Series* Connection Allowed |
Up to 2S |
Parallel* Connection Allowed |
Up to 8P (Max. continuous discharge current 0.5C when in Parallel) |
Case Structure |
Rugged mechanical design |
Safety |
UN38.3 Approved |
Size |
Perfect fit in N70 size battery box |
Dimensions (L x W x H) |
300 x 173 x 220mm |
Weight |
Approx. 15KG |
Warranty |
3 Years |
* No Connection of Series & Parallel Concurrently Allowed (Only either of the above)
| Pylontech RV12100 12.8V 100Ah Lithium Battery | |||
| Pylontech | RV 12V 100A LiFePO4 | $969.00 | |
Pylontech RV12100 12.8V 100Ah 1280Wh 4S4P Lithium Iron Phosphate (LiFePO4) Battery
High power 12.8V 100Ah lithium iron phosphate (LiFePO4) rechargeable battery
Rechargeable Lithium LiFePO4 high power modules to handle anything SLA can. Get 100% capacity utilisation at less than half the weight.
Pylontech RT12100 12.8V 100Ah 1280Wh Lithium Iron Phosphate (LiFePO4) IP67 Battery with RS485 / CAN / Bluetooth and Dry Contact Communications. Connect up to 4 in series and 4 in parallel for 48V 400Ah.
Pylontech 12V Series All-purpose Lithium Ion Battery
The Pylontech 12V series are all-purpose lithium-ion battery modules. With cutting edge LFP (Lithium Iron Phosphate) cells, embedded BMS (Battery Management System) and robust mechanical design, Pylontech RT12V series products provide inherent safety, extremely high reliability and zero maintenance. Compared to lead-acid based batteries with the same capacity, the Pylontech batteries have twice the usable capacity, more than 3 times the life cycle, with only 40% of the weight. They are the perfect replacement to lead acid-based batteries in applications such as marine, caravan/RV, golf carts and solar storage. A superior solution in all applications.
Pylontech RT12100G31 Key Features
- Auto-Balance Multiple Batteries in Parallel
- Connects multiple batteries in parallel safely without internal non-uniformity issues.
- Expandable up to 4 series and 4 parallel for up to 48V 400Ah
- Customise your system. 16 units can be scaled in a variety of series and parallel such as 4 Series 4 Parallel, 2 Series 8 Parallel, 1 Series 16 Parallel.
The internal Battery Management System (BMS) provides comprehensive protection to the battery and delivers sophisticated management of charging and discharging. The built-in battery also complies with the safety standard IEC62619 and is UN38.3 Certified, so you can use it with confidence.
Uncompromising QualityState-of-the-art battery cells ensure a lifespan of more than 4000 cycles, 100A continuous discharge current (200A for 30 seconds), and a wide range of working operating temperatures of -20 to -60°C
Upgraded waterproof & cold resistance built-in heaterIn addition to being waterproof, the RT12100G31 also has a built-in heater, so you can use it down to -20°C to and storage down to -40°C
Excellent BMS (Battery Management System)
Pylontech is one of the top manufacturers in the global market for household storage batteries. Pylontechs internal BMS monitors and protects overcharge, over-discharge, overcurrent, short circuit, temperature, etc. with high accuracy. In addition, the information grasped by BMS can be sent to the outside by Bluetooth or CAN communication. High-performance, power-saving BMS protects the internal battery firmly.
CommunicationsCAN, RS485, Bluetooth and Dry Contact communications enable flexible data transmission to meet the needs of different applications.
Pylontech RT12100G31 Advantages
- Twice the usable capacity (compared to the same capacity of FLA/AGM/GEL)
- Deep Cycle (Auto cut-off at 10V)
- Calendar life of 10+ years, the cycle life of 4000 times
- High charging current
- Embedded BMS
- RS485, CAN and Bluetooth 5 Connectivity
- Connect up to 4x Parallel and 4x Series (16 batteries in total)
- Zero maintenance
- Working Temperature -20 to -60°C
- Rugged mechanical design
- Ingress protection IP67 Rating - great for marine applications
- Built-in heater
- Serviceable design (marine grade stainless steel screws to replace BMS and/or cells)
This product is certified to UN38.3
This battery has been tested & complies with the UN Model Regulation, Manual of Test & Criteria, Part III, Subsection 38.3
Model |
RT12100 |
|---|---|
Nominal Voltage |
12.8V |
Nominal Capacity |
100Ah (1280Wh) |
Cycle Life (DOD - 80% under controlled conditions) |
>6000 cycles (90% DoD) @ 25ºC |
Maximum Charge Voltage |
14.2V - 14.6V (14.4V recommended) |
Max. continuous charge current |
50A |
Max. Pulse discharge current: (30 sec) |
200A |
Max. continuous discharge current |
100A |
Discharge Cut-Off Voltage |
10V |
Operating Discharge temperature |
-20 to -60°C |
Operating Charge temperature |
-0 to -60°C |
Storage temperature |
-40 to -60°C |
Short Circuit Protection |
Yes |
IP Rating |
IP67 Rating |
Series* Connection Allowed |
Up to 4S |
Parallel* Connection Allowed |
Up to 16P @ 12V Up to 8P @ 24V Up to 4P @ 48V |
Case Structure |
Rugged mechanical design |
Safety |
UN38.3 Approved |
Size |
G31 Size |
Dimensions (L x W x H) |
325 x 174 x 226mm |
Weight |
Approx. 13KG |
Warranty |
3 Years |
| Pylontech RT12100G31 12.8V 100Ah IP67 Lithium Battery | |||
| Pylontech | RT 12V 100A LiFePO4 | $1199.00 | |